SEK Electronics supplement

P9901-4F
302.85 €
Tax excluded
Quantity

Recycle Seal

This student experiment box requires accessories!

Student experiment equipment set for carrying out at least 75 experiments in electricity - electronics (basics) on the following topics:

  • Semiconductors (6 experiments)
  • Diodes (10 experiments)
  • Transistors (21 experiments)
  • Capacitors (15 experiments)
  • Rectifier circuits (2 experiments)
  • Multivibrator circuits (8 experiments)
  • Amplifier circuits (7 experiments)
  • Logic circuits (6 experiments)
Outstanding features:
  • NTL plug-in block system SE - the yellow original
    ⇒ Circuit diagrams can be implemented 1:1 - ideal and important for understanding electrical circuits at the beginning of electrical teaching
    ⇒ Complex electronic circuits can also be implemented (➜ SEK Electronics supplement 1 and 2)
  • NTL-plug-in blocks are consisting of ABS plastic housing and transparent, screwed base plates
    ⇒ Electrical components are clearly identifiable and easy to replace
  • Each NTL plug-in module has its corresponding electrical component symbol printed on its top side
  • PIB bridge rectifier with 4 red LEDs: at a frequency of 0.5 Hz, the students can visually monitor the rectification
    ⇒ ideal for everyone as an introduction to electronics
The SEK student experiments system by NTL:
  • Topic-oriented structure and division according to physical sub-areas
  • All areas of physics are covered
  • Didactically and thematically sensible division of the sub-areas into several boxes
  • Each part in the student box can also be ordered separately and purchased individually if required
  • Student experiment instructions based on the curriculum and ideally matched to the composition of the boxes
  • Clear arrangement of the box contents: only 1 material layer in all boxes, without confusing intermediate shelves
  • Extremely stable storage boxes, non-slip stackable - and made from 100% recycled material
  • Molded plastic box inserts do not become brittle and have a long service life
The standard scope of delivery of our SEK contains:
  • Complete equipment set for a group of pupils
  • Storage box incl. lockable lid
  • Individually shaped plastic box insert
  • Clear box storage plan in the lid

The experiment manuals are not included with our SEK!

You will find the corresponding experiment manual in the accessories tab for this SEK.

Boxeneinlage für P9901-4F SEB Elektronik - Ergänzung 1 + 2 (DEU)

P9901-4F Boxeneinlageplan (PDF) (141.72KB)

Plan for storage of all components for P9901-4F SEK Electronics supplement 1 + 2 (ENG)

P9901-4F Box insert plan (PDF) (140.12KB)

Plán rozloženia pre P9901-4F ŽEM Elektronika - doplnenie (SK)

P9901-4F Plán uloženia (PDF) (228.38KB)

List of all experimental topics that can be carried out with this set (ENG)

P9901-4F Index experiments (PDF) (80.01KB)

Auflistung aller Versuchsthemen, welche mit diesem Set durchgeführt werden können (DEU)

P9901-4F Index Versuchsthemen (P (90.65KB)

1. Semiconductors
EOS 1.1 PTC-resistor Photo of the experimental setup: EOS 1.1 PTC-resistor Symbolic image of a PDF document
EOS 1.2 NTC-resistor Photo of the experimental setup: EOS 1.2 NTC-resistor Symbolic image of a PDF document
EOS 1.3 Light dependent resistor (LDR) Photo of the experimental setup: EOS 1.3 Light dependent resistor (LDR) Symbolic image of a PDF document
EOS 1.4 Measuring the luminous intensity Photo of the experimental setup: EOS 1.4 Measuring the luminous intensity Symbolic image of a PDF document
EOS 1.5 VDR-resistor Photo of the experimental setup: EOS 1.5 VDR-resistor Symbolic image of a PDF document
EOS 1.6 Solar cell Photo of the experimental setup: EOS 1.6 Solar cell Symbolic image of a PDF document
2. Diodes
EOS 2.1 Silicon diode Photo of the experimental setup: EOS 2.1 Silicon diode Symbolic image of a PDF document
EOS 2.2 Forward voltage of a silicon diode Photo of the experimental setup: EOS 2.2 Forward voltage of a silicon diode Symbolic image of a PDF document
EOS 2.2.1 Characteristic lines of semiconductor diodes Photo of the experimental setup: EOS 2.2.1 Characteristic lines of semiconductor diodes Symbolic image of a PDF document
EOS 2.3 Diodes protect meters Photo of the experimental setup: EOS 2.3 Diodes protect meters Symbolic image of a PDF document
EOS 2.4 Light-emitting diode (LED) Photo of the experimental setup: EOS 2.4 Light-emitting diode (LED) Symbolic image of a PDF document
EOS 2.4.1 Forward voltage of an LED Photo of the experimental setup: EOS 2.4.1 Forward voltage of an LED Symbolic image of a PDF document
EOS 2.5 Indicators of polarity Photo of the experimental setup: EOS 2.5 Indicators of polarity Symbolic image of a PDF document
EOS 2.5.1 Indicators of polarity at A.C. with variable frequency Photo of the experimental setup: EOS 2.5.1 Indicators of polarity at A.C. with variable frequency Symbolic image of a PDF document
EOS 2.6 Zener diodes Photo of the experimental setup: EOS 2.6 Zener diodes Symbolic image of a PDF document
EOS 2.7 Stabilizing of voltage Photo of the experimental setup: EOS 2.7 Stabilizing of voltage Symbolic image of a PDF document
3. Transistors
EOS 3.1 Does a transistor consist of two diodes? Photo of the experimental setup: EOS 3.1 Does a transistor consist of two diodes? Symbolic image of a PDF document
EOS 3.1.1 How does a PNP-transistor behave? Photo of the experimental setup: EOS 3.1.1 How does a PNP-transistor behave? Symbolic image of a PDF document
EOS 3.2 Base current makes collector current possible (NPN-transistor) Photo of the experimental setup: EOS 3.2 Base current makes collector current possible (NPN-transistor) Symbolic image of a PDF document
EOS 3.2.1 Base current allows current at collector (PNP-transistor) Photo of the experimental setup: EOS 3.2.1 Base current allows current at collector (PNP-transistor) Symbolic image of a PDF document
EOS 3.3 The transistors as an amplifier Photo of the experimental setup: EOS 3.3 The transistors as an amplifier Symbolic image of a PDF document
EOS 3.3.1 Base connection (current amplification) Photo of the experimental setup: EOS 3.3.1 Base connection (current amplification) Symbolic image of a PDF document
EOS 3.3.2 Base connection (voltage amplification) Photo of the experimental setup: EOS 3.3.2 Base connection (voltage amplification) Symbolic image of a PDF document
EOS 3.3.3 Collector connection (current amplification) Photo of the experimental setup: EOS 3.3.3 Collector connection (current amplification) Symbolic image of a PDF document
EOS 3.3.4 Collector connection (voltage amplification) Photo of the experimental setup: EOS 3.3.4 Collector connection (voltage amplification) Symbolic image of a PDF document
EOS 3.3.5 Emittor connection (current amplification) Photo of the experimental setup: EOS 3.3.5 Emittor connection (current amplification) Symbolic image of a PDF document
EOS 3.3.6 Transfer characteristic of a NPN-transistor Photo of the experimental setup: EOS 3.3.6 Transfer characteristic of a NPN-transistor Symbolic image of a PDF document
EOS 3.3.7 Transfer characteristic of a PNP-transistor Photo of the experimental setup: EOS 3.3.7 Transfer characteristic of a PNP-transistor Symbolic image of a PDF document
EOS 3.3.8 Adjustment of the operating point Photo of the experimental setup: EOS 3.3.8 Adjustment of the operating point Symbolic image of a PDF document
EOS 3.3.9 Amplification free distortion due to base quiescent current Photo of the experimental setup: EOS 3.3.9 Amplification free distortion due to base quiescent current Symbolic image of a PDF document
EOS 3.4 Light triggered alarm Photo of the experimental setup: EOS 3.4 Light triggered alarm Symbolic image of a PDF document
EOS 3.5 Base voltage divider Photo of the experimental setup: EOS 3.5 Base voltage divider Symbolic image of a PDF document
EOS 3.6 Construction of a burglar alarm by means of trip wire Photo of the experimental setup: EOS 3.6 Construction of a burglar alarm by means of trip wire Symbolic image of a PDF document
EOS 3.7 Automatic illumination Photo of the experimental setup: EOS 3.7 Automatic illumination Symbolic image of a PDF document
EOS 3.8 Alarm by means of light barriers Photo of the experimental setup: EOS 3.8 Alarm by means of light barriers Symbolic image of a PDF document
EOS 3.9 Fire alarm Photo of the experimental setup: EOS 3.9 Fire alarm Symbolic image of a PDF document
EOS 3.10 Electric thermometer Photo of the experimental setup: EOS 3.10 Electric thermometer Symbolic image of a PDF document
4. Capacitors
EOS 4.1 A storage for electric charges Photo of the experimental setup: EOS 4.1 A storage for electric charges Symbolic image of a PDF document
EOS 4.2 A capacitor supplies base current Photo of the experimental setup: EOS 4.2 A capacitor supplies base current Symbolic image of a PDF document
EOS 4.3 Capacitance Photo of the experimental setup: EOS 4.3 Capacitance Symbolic image of a PDF document
EOS 4.3.1 Time switch Photo of the experimental setup: EOS 4.3.1 Time switch Symbolic image of a PDF document
EOS 4.4 A capacitor blocks D.C Photo of the experimental setup: EOS 4.4 A capacitor blocks D.C Symbolic image of a PDF document
EOS 4.5 Half-wave rectification Photo of the experimental setup: EOS 4.5 Half-wave rectification Symbolic image of a PDF document
EOS 4.6 Smoothing of rectified voltage Photo of the experimental setup: EOS 4.6 Smoothing of rectified voltage Symbolic image of a PDF document
EOS 4.7 Capacitors as A.C. resistance Photo of the experimental setup: EOS 4.7 Capacitors as A.C. resistance Symbolic image of a PDF document
EOS 4.7.1 Capacitive resistance at an A.C. of 50 Hz Photo of the experimental setup: EOS 4.7.1 Capacitive resistance at an A.C. of 50 Hz Symbolic image of a PDF document
EOS 4.7.2 Capacitive resistance Photo of the experimental setup: EOS 4.7.2 Capacitive resistance Symbolic image of a PDF document
EOS 4.8 Charged capacitors connected in series Photo of the experimental setup: EOS 4.8 Charged capacitors connected in series Symbolic image of a PDF document
EOS 4.9 Capacitors connected in series (determination of capacitance) Photo of the experimental setup: EOS 4.9 Capacitors connected in series (determination of capacitance) Symbolic image of a PDF document
EOS 4.10 Capacitors connected in parallel Photo of the experimental setup: EOS 4.10 Capacitors connected in parallel Symbolic image of a PDF document
EOS 4.11 A.C. resistors connected in series Photo of the experimental setup: EOS 4.11 A.C. resistors connected in series Symbolic image of a PDF document
EOS 4.12 Ohmic resistors, coil and capacitor in an A.C. circuit Photo of the experimental setup: EOS 4.12 Ohmic resistors, coil and capacitor in an A.C. circuit Symbolic image of a PDF document
EOS 4.13 Filter Photo of the experimental setup: EOS 4.13 Filter Symbolic image of a PDF document
5. Rectifier circuits
EOS 5.1 Principle of full-wave rectifying (mid-point tapping) Photo of the experimental setup: EOS 5.1 Principle of full-wave rectifying (mid-point tapping) Symbolic image of a PDF document
EOS 5.2 Application of full-wave rectifying Photo of the experimental setup: EOS 5.2 Application of full-wave rectifying Symbolic image of a PDF document
EOS 5.3 Bridge connection Photo of the experimental setup: EOS 5.3 Bridge connection Symbolic image of a PDF document
EOS 5.3.1 Bridge connection at A.C. with variable frequency Photo of the experimental setup: EOS 5.3.1 Bridge connection at A.C. with variable frequency Symbolic image of a PDF document
6. Multivibrator circuits
EOS 6.1 Bistable multivibrator Photo of the experimental setup: EOS 6.1 Bistable multivibrator Symbolic image of a PDF document
EOS 6.2 Discharging of a condenser Photo of the experimental setup: EOS 6.2 Discharging of a condenser Symbolic image of a PDF document
EOS 6.3 A condenser prevents base current Photo of the experimental setup: EOS 6.3 A condenser prevents base current Symbolic image of a PDF document
EOS 6.4 Monostable multivibrator Photo of the experimental setup: EOS 6.4 Monostable multivibrator Symbolic image of a PDF document
EOS 6.5 Flashing circuit Photo of the experimental setup: EOS 6.5 Flashing circuit Symbolic image of a PDF document
EOS 6.6 Multivibrator music Photo of the experimental setup: EOS 6.6 Multivibrator music Symbolic image of a PDF document
EOS 6.7 Music controlled by light Photo of the experimental setup: EOS 6.7 Music controlled by light Symbolic image of a PDF document
EOS 6.7.1 Music controlled by temperature Photo of the experimental setup: EOS 6.7.1 Music controlled by temperature Symbolic image of a PDF document
7. Oscillating circuits
EOS 7.1 Principle of a resonant circuit ( Parts of SEK Electromagnetism required ) Photo of the experimental setup: EOS 7.1 Principle of a resonant circuit ( Parts of SEK Electromagnetism required ) Symbolic image of a PDF document
EOS 7.1.1 Parallel resonant circuit ( Parts of SEK Electromagnetism required ) Photo of the experimental setup: EOS 7.1.1 Parallel resonant circuit ( Parts of SEK Electromagnetism required ) Symbolic image of a PDF document
EOS 7.1.2 Acceptor circuit ( Parts of SEK Electromagnetism required ) Photo of the experimental setup: EOS 7.1.2 Acceptor circuit ( Parts of SEK Electromagnetism required ) Symbolic image of a PDF document
EOS 7.2 Continuous oscillations ( Parts of SEK Electromagnetism required ) Photo of the experimental setup: EOS 7.2 Continuous oscillations ( Parts of SEK Electromagnetism required ) Symbolic image of a PDF document
EOS 7.3 LC-music ( Parts of SEK Electromagnetism required ) Photo of the experimental setup: EOS 7.3 LC-music ( Parts of SEK Electromagnetism required ) Symbolic image of a PDF document
8. Amplifier circuits
EOS 8.1 The resistance of human bodies Photo of the experimental setup: EOS 8.1 The resistance of human bodies Symbolic image of a PDF document
EOS 8.1.1 A transistor step controls a second step Photo of the experimental setup: EOS 8.1.1 A transistor step controls a second step Symbolic image of a PDF document
EOS 8.1.2 Alarm at failure of the heating Photo of the experimental setup: EOS 8.1.2 Alarm at failure of the heating Symbolic image of a PDF document
EOS 8.2 Automatic level measuring Photo of the experimental setup: EOS 8.2 Automatic level measuring Symbolic image of a PDF document
EOS 8.3 Lie detector Photo of the experimental setup: EOS 8.3 Lie detector Symbolic image of a PDF document
EOS 8.4 Microphone amplifier Photo of the experimental setup: EOS 8.4 Microphone amplifier Symbolic image of a PDF document
EOS 8.5 Sum and difference amplifier Photo of the experimental setup: EOS 8.5 Sum and difference amplifier Symbolic image of a PDF document
EOS 8.6 A motor armature signals its position Photo of the experimental setup: EOS 8.6 A motor armature signals its position Symbolic image of a PDF document
EOS 8.7 Direct-current motor without commutator Photo of the experimental setup: EOS 8.7 Direct-current motor without commutator Symbolic image of a PDF document
9. Logic circuits
EOS 9.1 The logic AND-circuit ( Parts of SEK Electromagnetism required ) Photo of the experimental setup: EOS 9.1 The logic AND-circuit ( Parts of SEK Electromagnetism required ) Symbolic image of a PDF document
EOS 9.2 The logic OR-circuit ( Parts of SEK Electromagnetism required ) Photo of the experimental setup: EOS 9.2 The logic OR-circuit ( Parts of SEK Electromagnetism required ) Symbolic image of a PDF document
EOS 9.3 The logic NOT-circuit Photo of the experimental setup: EOS 9.3 The logic NOT-circuit Symbolic image of a PDF document
EOS 9.4 AND-circuit Photo of the experimental setup: EOS 9.4 AND-circuit Symbolic image of a PDF document
EOS 9.5 OR-circuit Photo of the experimental setup: EOS 9.5 OR-circuit Symbolic image of a PDF document
EOS 9.6 NOT-circuit Photo of the experimental setup: EOS 9.6 NOT-circuit Symbolic image of a PDF document
EOS 9.7 NAND-circuit Photo of the experimental setup: EOS 9.7 NAND-circuit Symbolic image of a PDF document
EOS 9.8 NOR-circuit Photo of the experimental setup: EOS 9.8 NOR-circuit Symbolic image of a PDF document
Required accessories:
Quantity Item no. Description
1x P9901-4D SEK Electricity 1
- Student experiment equipment set for carrying out 46 experiments in the field of electricity on the following topics:
• Fundamental principles (8 experiments)
• Electrical resistance (25 experiments)
• Thermal energy derived from electrical energy (5 experiments)
• Work and power (2 experiments)
• Electrochemistry (6 experiments)
NTL-Item: P9901-4D SEK Electricity 1
1x P9160-4F Manual "Electronics", english, book
- Student workbook with at least 75 experiments on the topic "Electricity - Electronics"
- Matched to the student experiment box SEK Electronics, supplement 1 & 2
NTL-Item: P9160-4F Manual "Electronics", english, book
1x Low-voltage power supply
- DC voltage: 0 ... 12 V
- AC voltage: 0/3/6/12 V
1x Function generator
- Frequency range 1: 0 ... 100 Hz, sinusoidal oscillation
- Frequency range 2: 0 ... 1,000 Hz, sinusoidal oscillation
1x Voltmeter
- Measuring range 1: 0 ... 30 V
- Measuring range 2: 0 ... 10 V
- Measuring range 3: 0 ... 3 V
- Measuring range 4: 0 ... 1 V
1x Ammeter
- Measuring range 1: 0 ... 100 mA
- Measuring range 2: 0 ... 30 mA
- Measuring range 3: 0 ... 10 mA
We recommend the following optional accessories:
Quantity Item no. Description
1x P3130-3D Low-voltage power supply with digital display
- Universal current and voltage supply for student experiments on the subject of Electricity theory"
- Infinitely variable and stabilised DC voltage
- with digital display of the DC voltage
- Electronic overload protection
- Of course RiSU-compliant in accordance with the Guideline for Safety in Teaching (RiSU) of the Standing Conference of the Ministers of Education and Cultural Affairs KMK in the update of 2023
NTL-Item: P3130-3D Low-voltage power supply with digital display
1x P3120-3F Function generator Benny
- Universal function generator for student experiments on the topics of mechanics and electricity
- Sine, triangle and square wave signal
- Frequency range: 0.1 Hz ... 100 kHz
NTL-Item: P3120-3F Function generator Benny
1x P3212-20 Multimeter analogue 12
- Unique analogue multimeter for student experiments in electricity theory
- Didactically designed and specially tailored to pupils' needs: the large mirror scale
- All measuring ranges available in DC and AC
- 1 mV final value range for measuring very low voltages even without a preamplifier
NTL-Item: P3212-20 Multimeter analogue 12
1x P3245-1M Multimeter digital, True RMS
- Universal digital multimeter for student experiments
- Safety category: CAT IV (up to 600 V), CAT III (up to 1,000 V)
- Fuse protection in all current measuring ranges
- incl. temperature sensor
NTL-Item: P3245-1M Multimeter digital, True RMS
1x P3250-1M Multimeter digital “BT“, True RMS
- Technically identical to P3245-1M, but with Bluetooth data transmission.g
- Free apps for Android™, iOS and iPadOS ®
NTL-Item: P3250-1M Multimeter digital “BT“, True RMS
1x P9902-5P SEK Electromagnetism
- Student experiment equipment set for carrying out 38 experiments in the field of electricity - electromagnetism on the following topics:
• Thermal energy from electrical energy (3 experiments)
• Work and power (1 experiment)
• Electromagnetism (8 experiments)
• Kinetic energy from electric energy (6 experiments)
• Electromagnetic induction (20 experiments)
NTL-Item: P9902-5P SEK Electromagnetism

You might also like